 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| www.fairchildsemi.com KA2S0765 Fairchild Power Switch(FPS) Features * * * * * * * * * Wide operatimg frequency range up to (150kHz) Pulse by pulse over current limiting Over load protection Over voltage protecton (Min. 23V) Internal thermal shutdown function Under voltage lockout Internal high voltage sense FET External sync terminal Latch up Mode Description The Fairchild Power Switch(FPS) product family is specially designed for an off line SMPS with minimal external components. The Fairchild Power Switch(FPS) consist of high voltage power SenseFET and current mode PWM controller IC. control IC features a trimmed oscillator, under voltage lock-out, leading edge blanking, optimized gate turn-on/turn-off driver, thermal shut down protection, over voltage protection, temperature compensated precision current sources for loop compensation and fault protection circuit. compared to discrete MOSFET and controller or RCC switching converter solution, a Fairchild Power Switch(FPS) can reduce total component count, design size, weight and at the same time increase & efficiency, productivity, and system reliability. It has a basic platform well suited for cost-effective Monitor power supply. TO-3P-5L 1 1.DRAIN 2. GND 3. Vcc 4. FB 5. Sync Internal Block Diagram #3 VCC 32V 5V Vref - 5V + 6.4V #4 FB 2A 1mA 2.5R 1R 9V + 7.5V - + 25V - Thermal S/D OVER VOLTAGE S/D - + 0.1V S R Q #2 GND OSC S R L.E.B Q Good logic Internal bias #1 DRAIN SFET #5 Sync Power on reset Rev.1.0.2 (c)2001 Fairchild Semiconductor Corporation KA2S0765 Absolute Maximum Ratings Characteristic Maximum Drain voltage (1) Symbol VD,MAX VDGR VGS IDM (3) Value 650 650 30 28.0 570 7.0 5.6 30 -0.3 to VSD 140 1.11 -25 to +85 -55 to +150 Unit V V V ADC mJ ADC ADC V V W W/C C C Drain Gate voltage (RGS=1M) Gate source (GND) voltage Drain current pulsed (2) Single pulsed avalanche energy EAS ID ID VCC,MAX VFB PD Continuous drain current (TC=25C) Continuous drain current (TC=100C) Maximum Supply voltage Input voltage range Total power dissipation Operating ambient temperature Storage temperature Derating TA TSTG Note: 1. Tj=25C to 150 2. Repetitive rating: Pulse width limited by maximum junction temperature 3. L=24mH, VDD=50V, RG=25, starting Tj=25 C 2 KA2S0765 Electrical Characteristics (SFET part) (Ta = 25C unless otherwise specified) Characteristic Drain source breakdown voltage Zero gate voltage drain current Static drain source on resistance (note) Forward transconductance (note) Input capacitance Output capacitance Reverse transfer capacitance Turn on delay time Rise time Turn off delay time Fall time Total gate charge (gate-source+gate-drain) Gate source charge Gate drain (Miller) charge Note: Pulse test: Pulse width < 300S, duty cycle < 2% 1 S = --R Symbol BVDSS IDSS RDS(ON) gfs Ciss Coss Crss td(on) tr td(off) tf Qg Qgs Qgd Test condition VGS=0V, ID=50A VDS=Max., Rating, VGS=0V VDS=0.8Max., Rating, VGS=0V, TC=125C VGS=10V, ID=4.0A VDS=15V, ID=4.0A VGS=0V, VDS=25V, f=1MHz VDD=0.5BVDSS, ID=7.0A (MOSFET switching time are essentially independent of operating temperature) VGS=10V, ID=7.0A, VDS=0.5BVDSS (MOSFET switching time are essentially independent of operating temperature) Min. 650 3.0 - Typ. 1.25 1600 310 120 25 55 80 50 9.3 29.3 Max. 50 200 1.6 72 - Unit V A mA W S pF nS nC 3 KA2S0765 Electrical Charcteristics (CONTROL part) (Ta = 25C unless otherwise specified) Characteristic UVLO SECTION Start threshold voltage Stop threshold voltage OSCILLATOR SECTION Initial accuracy Frequency change with temperature (2) Maximum duty cycle FEEDBACK SECTION Feedback source current Shutdown Feedback voltage Shutdown delay current SYNC. & SOFT START SECTION Soft start voltage Soft start current Sync threshold voltage(3) REFERENCE SECTION Vref Ta=25C Output voltage (1) Vref/T -25C Ta +85C Temperature Stability (1)(2) CURRENT LIMIT (SELF-PROTECTION) SECTION KA2S0765 Peak Current Limit IOVER PROTECTION SECTION Thermal shutdown temperature (Tj) (1) Over voltage protection voltage TOTAL DEVICE SECTION Start Up current Operating supply current (control part only) VCC zener voltage ISTART IOP VZ VCC=14V Ta=25C ICC=20mA 0.1 6 30 0.3 12 32.5 0.55 18 35 mA mA V TSD VOVP 140 23 160 25 28 C V 4.80 4.40 5.00 0.3 5.00 5.20 0.6 5.60 V mV/C A VSS ISS VSYTH VFB=2V Sync & S/S=GND Vfb=5V 4.7 0.8 6.0 5.0 1.0 6.4 5.3 1.2 6.8 V mA V IFB VSD Idelay Ta=25C, Vfb=GND Ta=25C, 5V Vfb VSD 0.7 6.9 1.4 0.9 7.5 1.8 1.1 8.1 2.2 mA V A FOSC F/T Dmax Ta=25C -25C Ta +85C 18 92 20 5 95 22 10 98 kHz % % VSTART VSTOP After turn on 14 9 15 10 16 11 V V Symbol Test condition Min. Typ. Max. Unit Note: 1. These parameters, although guaranteed, are not 100% tested in production 2. These parameters, although guaranteed, are tested in EDS(water test) process 3. The amplitude of the sync. pulse is recommended to be between 2V and 3V for stable sync. function. 4 KA2S0765 Typical Performance Characteristics (These characteristic graphs are normalized at Ta = 25C) Fig.1 Operating Frequency 1.2 1.15 1.1 1.05 Fosc 1 0.95 0.9 0.85 0.8 -25 0 25 50 75 100 125 150 1.2 1.15 1.1 1.05 Ifb 1 0.95 0.9 0.85 0.8 -25 Fig.2 Feedback Source Current 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 1. Operating Frequency Figure 2. Feedback Source Current Fig.3 Operating Current 1.2 1.15 1.1 1.05 Iop 1 0.95 0.9 0.85 0.8 -25 1.1 1.05 Fig.4 Max Inductor Current IIpeak 1 over 0.95 0.9 0.85 0 25 50 75 100 125 150 0.8 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 3. Operating Supply Current Figure 4. Peak Current Limit Fig.6 Start Threshold Voltage 1.15 1.1 1.05 1.5 1.3 Fig.5 Start up Current Istart 1.1 0.9 0.7 0.5 -25 Vstart 1 0.95 0.9 0 25 50 75 100 125 150 0.85 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 5. Start up Current Figure 6. Start Threshold Voltage 5 KA2S0765 Typical Performance Characteristics (Continued) (These characteristic graphs are normalized at Ta = 25C) Fig.7 Stop Threshold Voltage 1.15 1.1 1.05 1.15 1.1 1.05 Fig.8 Maximum Duty Cycle Vth(L) Vstop 1 0.95 0.9 0.85 -25 0 25 50 75 100 125 150 Dmax 1 0.95 0.9 0.85 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 7. Stop Threshold Voltage Figure 8. Maximum Duty Cycle Fig.9 Vcc Zener Voltage 1.2 1.15 1.1 1.05 Vz 1 0.95 0.9 0.85 0.8 -25 1.15 1.1 1.05 Fig.10 Shutdown Feedback Voltage Vsd 1 0.95 0.9 0 25 50 75 100 125 150 0.85 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 9. VCC Zener Voltage Figure 10. Shutdown Feedback Voltage Fig.11 Shutdown Delay Current 1.2 1.15 1.1 1.05 Idelay 1 0.95 0.9 0.85 0.8 -25 1.15 1.1 1.05 Fig.12 Over Voltage Protection Vovp 1 0.95 0.9 0 25 50 75 100 125 150 0.85 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 11. Shutdown Delay Current Figure 12. Over Voltage Protection 6 KA2S0765 Typical Performance Characteristics (Continued) (These characteristic graphs are normalized at Ta = 25C) Fig.13 Soft Start Voltage 1.15 1.1 1.05 2.5 2 1.5 Fig.14 Drain Source Turn-on Resistance Vss 1 0.95 0.9 0.85 -25 0 25 50 75 100 125 150 Rdson )1 ( 0.5 0 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 13. Soft Start Voltage Figure 14. Static Drain-Source on Resistance 7 KA2S0765 Package Dimensions TO-3P-5L 8 KA2S0765 Package Dimensions (Continued) TO-3P-5L (Forming) 9 KA2S0765 Ordering Information Product Number KA2S0765-TU KA2S0765-YDTU TU : Non Forming Type YDTU : Forming Type Package TO-3P-5L TO-3P-5L(Forming) Rating 650V,7A Operating Temperature -25C to +85C DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. www.fairchildsemi.com 10/17/01 0.0m 001 Stock#DSxxxxxxxx 2001 Fairchild Semiconductor Corporation 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. |
Price & Availability of KA2S0765
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |